• Two-Color Peeler Plastic Injection Mould

    Two-Color Peeler Plastic Injection Mould

    The core of two-color peeler plastic injection mould is made inserted, which can be replaced for different design. As the result of product being short, we design the products be injected horizontally that allow product to have lesser parting line and ejector mark.

    Read More
  • Multi-color Basin Plastic Injection Mould

    Multi-color Basin Plastic Injection Mould

    The characteristic of this kind of multi-color injection moulding is to transform the general single color product into a multi-color mixed product without changing the mould, making them like various grain patterns such as wood grain, marble, jadeite and so on, without having to go through two processing procedures such as spray painting and water dyeing.

    Read More
  • Threaded Cap Plastic Injection Mould

    Threaded Cap Plastic Injection Mould

    Cap size: ø90.7 X 93 X 25mm Cap weight: 36gm Material: HDPE Mold: 4 cavities The thread part of this cap is designed with thread rotation off, and the motor device is used to drive the gear to rotate. The cap must be designed with a stop device to prevent the product from following the rotation when the thread rotates, resulting in the scratch of the cap thread. After the thread part of the cap is separated, use the ejector plate to eject. Compared with thread strength and thread rotation, thread rotation is more difficult to make, which requires high-precision processing equipment, high installation accuracy and accurate positioning between plates, otherwise it is easy to cause the problem of parts stuck and motor or oil cylinder not moving.

    Read More
  • Bathroom Corner Shelf Plastic Injection Mould

    Bathroom Corner Shelf Plastic Injection Mould

    The bathroom corner shelf is well-designed. The shape is triangle, which is appropriate to assemble in the corner. It has three spaces and two covers. For the first compartment it is out of cover, which is suitable for the waterproof commodity such as toothbrush set and shampoo whose size is taller. For the second compartment, you are suggested to put toilet paper and sanitary product into for preventing them from wet. As to the last also the smallest compartment, it is the best place to keep soap inside. At the bottom of the shelf has three hooks, you can hang towels, bath ball or anything you need in your bathroom.

    Read More
  • 16 Holes Plastic Dish Rack Injection Mould

    16 Holes Plastic Dish Rack Injection Mould

    DISH RACK 16 HOLES Product Size: 489 x 489 x 100mm Mold Design: 1. Cavity and Core made by splicing inserts 2. High-efficiency cooling system 3. 4 sliders design for Core with oil cylinders 4. Runner Gate with 5 tips Hot Runner to Submarine Gate

    Read More
  • Straw Handle Cup Plastic Injection Mould

    Straw Handle Cup Plastic Injection Mould

    This straw handle cup is divided into two sets of molds, one is the cup body and the other is the cup cover. In design, the cup body cavity 2 spring block slides. When opening the mold, it depends on the pull hook on the mold core side to start in an instant, and then the spring pushes the spring block out, and the mold core side directly relies on the machine to push the ejector plate to eject the product and drop. When the cup cover is opened, slide the 2 sliding blocks on one side of the core to both sides through the inclined guide post to separate the sliding blocks from the product. The 2 sliding blocks are designed on the pusher plate to eject the product as a whole.

    Read More
  • Mammoth Puzzle Toy Plastic Injection Mould

    Mammoth Puzzle Toy Plastic Injection Mould

    The mold is simple 2-plate mold structure, but because it is a puzzle product, there are a lot of small parts, the positions between parts and the pouring points are very skillful, if the arrangement is not good, there will be flash problems, air trap problem. Products are ejected out by pins. There are many ejectors in this mold, so ejector balance of ejector plate is very important. The most characteristic is that the mold runner is also a part of the product, is the product frame and fixed base.

    Read More
  • 1L Juice Blender Plastic Injection Mould

    1L Juice Blender Plastic Injection Mould

    For this juice mixer mold, the most important point is the high-end polish. The mold should be polished carefully to reach high transparency. As there are two big sliders to form the part, the parting line on the handle part is important, too. The parting line should be as less as possible to avoid flash and cutting customers’ fingers while using.

    Read More
  • 48L Laundry basket Plastic Injection Mould

    48L Laundry basket Plastic Injection Mould

    Laundry Basket Size: 489.2 X 622.7 X 233.9mm Basket Weight: 0.59 kgs Gate system: 5 tips Hot Runner Not all molding applications are suitable for runner-less molding. Some materials are heat sensitive and the time to temperature relationship - especially when the shot size is very small - can be a problem. Some families of parts, for handling and orientation purposes, may be best kept attached to the runner until they reach another downstream operation. In other instances, the required volume of parts may be so small that the added cost of the hot runner system to the mold price cannot be justified.

    Read More
Please feel free to give your inquiry in the form below. We will reply you in 24 hours.
* Email :
Company :
  • Name :

  • Phone:

Message :