• Two-Color plastic Lighter handle Injection Mould

    Two-Color plastic Lighter handle Injection Mould

    Most two-color lighter handles are made from plastic injection molds with rotating shafts. The rotating shaft process or the rotating core process means that the two-color plastic injection mold is not rotated by the injection molding machine, but the core is rotated by the injection molding machine or the injection mold cylinder. When the injection molded part is made into the second color, the controller of the injection molding machine will send a signal of the core pulling system, rotate the first core of the mold to the second position of the core, and then perform the injection of the second color.

    Read More
  • Foldable/Portable Outdoor Camping/Cleaning Double Component Bucket Mould

    Foldable/Portable Outdoor Camping/Cleaning Double Component Bucket Mould

    Product Size: 46x30.3x20.4cm Material: PP+TPE Weight: 580G - Durable and tough material, essential barrels for home camping. - Collapsible storage, clean and neat, does not take up space - Excellent texture, abrasion resistance, high and low temperature resistance, good grip

    Read More
  • Baby Walker Plastic Injection Mould

    Baby Walker Plastic Injection Mould

    In order to reduce the weight of baby walker, most of parts are made by plastic. On the other hand, plastic parts are stronger and colorful. Therefore, the quality of plastic parts of baby walker become very important. The key point of plastic injection mould for making baby walker is to get smooth surface and parting line to avoid injury against babies. Meanwhile, the assembly among of all plastic parts for baby walker is required flat without difference in level, prevent from collapse, enough strong and so on. It has to pay attention on the shrinkage of molds design and precise mold fabrication in order to get perfect assembly of baby walker, especially the small toy parts.

    Read More
  • Double Color Plastic Fruit Bowl Injection Mould

    Double Color Plastic Fruit Bowl Injection Mould

    Most of customers don’t want to invest double color injection machine. However, you can consider to produce two plastic products on your double color machine in future, or produce only one plastic part on double color machine. It won’t leave your double color injection machine unused if double color products range has not yet been developed too much. Two-color plastic injection products become more popular at market day by day, it is right time to invest and develop double color plastic products at this moment.

    Read More
  • Threaded Cap Plastic Injection Mould

    Threaded Cap Plastic Injection Mould

    Cap size: ø90.7 X 93 X 25mm Cap weight: 36gm Material: HDPE Mold: 4 cavities The thread part of this cap is designed with thread rotation off, and the motor device is used to drive the gear to rotate. The cap must be designed with a stop device to prevent the product from following the rotation when the thread rotates, resulting in the scratch of the cap thread. After the thread part of the cap is separated, use the ejector plate to eject. Compared with thread strength and thread rotation, thread rotation is more difficult to make, which requires high-precision processing equipment, high installation accuracy and accurate positioning between plates, otherwise it is easy to cause the problem of parts stuck and motor or oil cylinder not moving.

    Read More
  • Plastic Soap Box Injection Mould

    Plastic Soap Box Injection Mould

    The soap box must have the following design: 1. Anti-dip strip design. The anti-dip strip on the surface of the soap box can support the soap to a greater extent and reduce the probability of the soap soaking. 2. Drain tank design, convenient drainage. Soap box of the drain tank, convenient the water to flow out. 3. The bottom foot is designed to ensure that the soap box is at a certain height from the table. Even if there is water around the soap box, it will not be deposited in place.

    Read More
  • Double Color Wheel of Toy Car Plastic Injection Mould

    Double Color Wheel of Toy Car Plastic Injection Mould

    This double color wheel is made by PP of wheel frame and TPE of outer soft part. PP is rigid material which is good enough to support the weight of toy car. The weight of PP is lighter than steel frame, it is suitable for making toys. TPE could be produced by traditional injection molding machine, meanwhile, PP and TPE could be injected and plasticized together well, not easy to be separated by force. The mold is designed for rotating double color injection moulding process. The rotary double color injection mold is composed with two molds, the first mold is for making PP part, second mold for TPE part after PP part being injected and rotated to second position.

    Read More
  • High quality PC Pebbled Bowl Mould

    High quality PC Pebbled Bowl Mould

    Pebbled Bowls offer an elegant, shatter-proof take on the classic salad bowl, enhancing presentation and menu offerings. This selection of bowls is ideal for catering, outdoor events, and buffets, with a variety of sizes to suit fruit, snacks, and desserts. With a textured glass look on the outside, the interior is smooth for easy cleaning by hand or commercial dishwasher. Made of virtually unbreakable anti-wear for years of dependable service.

    Read More
  • Plastic Cup Injection Mould

    Plastic Cup Injection Mould

    Plastic Cups are containers for drinks and tea. Usually made of PP and PS material. Generally used in beverage stores, hot and cold drink stores, milk tea shops, hotels, restaurants, and coffee shops, which provide a variety of plastic cup drinks to go and on-site.

    Read More
Please feel free to give your inquiry in the form below. We will reply you in 24 hours.
* Email :
Company :
  • Name :

  • Phone:

Message :